Skip to main content Skip to search Skip to main navigation

C3-R20N/DC24V

可用的触点材料 AgNi
建议最小通断负载 10 mA / 10 V
最大触点负载 AC-1 10 A / 250 V AC-1
最大触点负载 DC-1 10 A / 30 V DC-1
机械耐久性(循环) ≥ 20 000 000
浪涌电流 30 A, 20 ms
联系次数 2 CO
额定电流 10 A
额定负载 AC-1 时的电气耐久性(周期) ≥ 500 000
额定负载交流 2 500 VA

授权 UKCA,CE,cURus,EAC,CSA,CCC
标准 IEC/EN 61810,IEC/EN 60947

关断脉冲功率 AC 0.3 VA, DC 0.5 W
吸合电压 ≤ 0.8 UN
工作电压范围 0.8 UN … 1.1 UN
接通脉冲电源 AC 1.8 VA, DC 1.5 W
释放电压 ≤ 0.8 UN
额定电压 见表 产品参考

电流类型 直流
额定电压 24 V

500 V 绝缘电阻 ≥ 1 GΩ
污染等级 3
测试电压断开触点 1 kV / 1 min
测试电压触点/触点 2.5 kV / 1 min
触点/线圈测试电压 2.5 kV / 1 min
过电压类别 III

外壳材料 PA / PC
存储温度(无冰) -40 … 80 °C
工作温度 -40 … 60 °C
最小脉冲长度 接通/断开 50
重量 81 g
额定负载下的最大开关频率 1 200 / h
授权
Remanenzrelais

A latching relay is a bistable relay that retains its switching state even if the supply voltage is interrupted. This means that the last selected switching position - whether switched on or off - remains reliably stored until the relay is deliberately switched over.

A latching relay is used wherever the switching status must be retained after a power failure or interruption. This means that installations or systems can continue to operate safely and stably after an interruption without having to reset the status.

The most important advantages include high energy efficiency and operational reliability. Energy is only required during the changeover, but not to maintain the status. At the same time, the ability to maintain the switching state even in the event of a loss of voltage provides additional reliability and protection against unwanted changes in operation.

A remanence relay works through magnetic remanence: when the relay is switched, residual magnetism remains in the magnetic core, which keeps the armature in its position even if the supply voltage is switched off. The switching state is therefore stored stably until a new control signal generates an opposite magnetic field that compensates for the existing residual magnetism. Only then is the relay deliberately switched into the new state. In this way, it only requires energy during the switching process and combines high efficiency with operational reliability.

Latching (remanence) versions are available for our industrial relay series C3, C4, C5 and C9. In the product code, they are identified by the letter R in the 3rd position: C3-R*, C4-R*, C5-R*, C9-R*.

In the railway sector, we offer latching versions for the R3-R.

当保持继电器两个控制输入同时接通时,A1(ON)始终优先于A3(OFF)。

Skip product gallery

配件

S3-L (SK-3006)
S3-L (SK-3006)

用于 R10 继电器的 5 针插座

S3-B
S3-B

- 10 A @ 300 V
- 螺钉端子

S3-S
S3-S

- 10 A @ 250 V
- 螺钉端子

S3-M
S3-M

10 A @ 250 V
- 用于时间或监控模块的模块舱
- 螺钉端子

S3-M0
S3-M0

10 A @ 250 V
- 用于时间或监控模块的模块舱
- 螺钉端子

S3-M1
S3-M1

10 A @ 250 V
- 用于时间或监控模块的模块舱
- 螺钉端子