CMS-10R-DA/DC12-48V-Z1-KIT1

Device kit for Zone 1: Worldwide
1x CMS-10R-DA/DC12-48V-Z1
1x HDR-15-24 power supply
1x CMS-ANT-MAG2/2.5M antenna

CMS-10R-DA/DC12-48V messaging system
Remote control of outputs and status queries of inputs and outputs via SMS, pager, voice call, push/email notification, remote configuration via web browser, application available for Android/iOS devices, supported communication standards GSM (2G) / UMTS (3G) / LTE (4G), integrated eSIM, operating voltage: 10 ... 48 V DC, Inputs: 6 x digital/analogue combination, Outputs: 4 x changeover contact (10 A / 250 V AC), 50 mm antenna, Power consumption 1 W, Operating temperature range -25 ... 55 °C, IP40, 5 TE DIN, grey plastic housing

Current type	DC
Nominal voltage	12 V-48 V

Antenna connector type	SMA female
Antenna impedance	50 Ω
Antenna jack torque (max)	1
Antenna return loss	> 10 dB
Communication Standards	E-GSM (2G), E-UTRA (3G), LTE (4G)
eSIM	Embedded
Frequency bands Z1	E-GSM: B2, B3, B5, B8 \| E-UTRA: B1, B2, B4, B5, B6, B8, B19 \| LTE-FDD: B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B28 \| LTE-TDD: B38, B39, B40, B41
Frequency bands Z2	E-GSM: B3, B8 \| E-UTRA: B1, B8 \| LTE-FDD: B1, B3, B7, B8, B20, B28A
Network coverage	Weltweit

Classification	Manual Control (IEC 60730-1)
Operation	Type 1 (IEC 60730-1)
Software class	Class A (IEC 60730-1)

Housing material	PA
Ingress Protection	IP 40
Mounting	DIN Rail (IEC 60715) and Panel mount
Operation Altitude	Max. 2 000 m / 6 562 ft over sea level (without derating)
Operation Position	any
Operation temperature	-25 … 70 °C / -13 ... 158 °F
Relative huminity, no condensation	10 … 95 %
Storage temperature (no ice)	-40 … 85 °C / -40 ... 185 °F
Weight	260 g

Logic level '0' digital inputs	< 4.0 V DC
Logic level '1' digital inputs	> 6.0 V DC
Maximal voltage digital inputs	48 V DC
Measurement category	2
Nominal range analogue voltage inputs	0 ... 10 V, Compliant with IEC 60381-2
Number of analogue voltage / digital inputs	6
Resolution of analogue inputs	12
Sampling rate per channel	10
Voltage input impedance	196 kΩ

Insulation rating between all ports	2 kV / 1 min
Insulation type	Reinforced
Overvoltage category	II
Pollution degree	2
Rated impulse voltage	2.5 kV / 1 min
Shock/vibration proof	IEC 61373

Contact material	AgNi
Electrical endurance at rated load AC-1 (cycles)	> 30 000
Maximum switching voltage	400 V AC
Number of relay outputs	4
Rated current AC-1	10 A
Rated load AC-1	3
Rated voltage	250 V AC
Recommended minimum load	10 mA, 12 V
Type of terminal	CO

Additional power consumption per output	0.45 W
Maximum power consumption	6 W
Nominal operating voltage	10 ... 48 V DC
Nominal voltage	10 ... 48 VDC
Operating voltage range	8.4 ... 60 V DC
Typical power consumption (without any output set)	< 1 W

Approvals	CE,UKCA
Standards	IEC/EN/BSI/UL/CSA 60730,CISPR 32 / EN 55032,IEC 61000-6-2/-3,ETSI EN 301511,ETSI EN 301908-1/-2/-13,IEC 60381-1/-2,IEC 62368-1,IEC/EN/BSI/AS/NZS/SANS 62368

Conductor cross section control / main circuit	4 mm² / AWG12 (Wire), 2.5 mm² / AWG14 (Stranded), 1.00 mm² / AWG17 (Ferrule). Use copper conductors only.
Contact type control / main circuit	Screw connection
Dual sleeve control / main circuit	1
Max. wire count control / main circuit	2
Nominal screw torque control / main circuit	0.5 Nm / 4.425 lbf in
Screwdrive control / main circuit	PZ2
Stripping Length control / main circuit	8 mm / 0.31"

Approvals

Data sheet

Helpful documents on the "CMS-10R-DA/DC12-48V-Z1-KIT1"

Android application battery optimisation
App installation instructions
Commissioning via the ComatReleco IoT portal
Installation Guide
Quick guide for installers
Safety instructions
User information CH
User information EU
User manual

3D-models "CMS-10R-DA/DC12-48V-Z1-KIT1"

CMS-10R_without_antenna.zip / STEP file
CMS-10R_with_antenna.zip / STEP file
HDR-15-zip / STEP file
CMS-10R_DrillPlan.zip / DXF file
CMS-10R_DrillPlanPDF.PDF

Release Notes "CMS-10R-DA/DC12-48V-Z1-KIT1"

Documents "CMS-10R-DA/DC12-48V-Z1-KIT1"

CMS-10F - CMS-10R comparison brochure
Service profiles for Switzerland
Service profiles worldwide
CMS-10R: Product brochure

Tools "CMS-10R-DA/DC12-48V-Z1-KIT1"

IoT portal

Google Play Store

Apple Store

Error messages

Mobile payment with the phone not allowed

This message appears when the country of origin of the credit card does not match the country where it is being used. For legal reasons, the European Union requires a double location check. The system reviews the country of origin of the credit card and the location of the IP address. Both must match. If the device is in Switzerland but the card is issued in another country, the payment is rejected for legal reasons. A possible alternative is to use a Swiss credit card within Switzerland.